Re: How hypermesh handle CATIA CAD format in import?
I have CATIA geometry reader installed and work fine. The question is just for curiosity on how Hypermesh takes care of CATIA geometry format in importing. I just learned that when Moldflow import...
View ArticleFATAL ERROR # 8011
I am doing the tutorial OS-2098: Topology Optimization of an Excavator Arm Model, and when I tried to run the optimization I get the following error message: ** FATAL ERROR # 8011 *** DELETE detects...
View ArticleRe: Error 4001
To install the latest update for HyperWorks please go to the link below, remember you must have a client log in (you must be registered as a client)...
View ArticleRe: FATAL ERROR # 8011
Hi, can you please let us know what are all the updates installed on your machine? please use the link below to know the updates:...
View ArticleClik here to view.
Loadstep for joint model
Dear administrator, I would like to ask which loadstep should I define for using FE-joints. The loadstep linear-static ignores the 1d fe-joints that I have created, I could fix the model using springs...
View ArticleRe: Loadstep for joint model
Hi Vitor, Joints which were created will work for OptiStruct Multi Body Dynamics simulation. In such case you can use analysis type as multibody dynamic while creating loadstep.
View ArticleRe: Error 4001
Update installed, keep on getting the same error message..."NLGEOM subcase 1, starter running ... *** ERROR # 4001 *** Running RADIOSS starter, 1 ERROR and 0 WARNINGs have been detected. They are...
View ArticleRe: FATAL ERROR # 8011
I have updated to the latest version and now the problem is solved. Thank you.
View ArticleHow to couple optistruct with Acusolve?
Hi all, I am thinking about using Optistruct and Acusolve together to optimize the composite layup of a front wing of a race car. My problem is that I am not clear about how to extract fluid simulation...
View ArticleRe: Error 4001
Hi, During bulk to block conversion (NLGEOM) solver writes a separate component and property for each element in the .rad deck and this creates a memory issue. Since you have orthotrpic properties,...
View ArticleRe: How to couple optistruct with Acusolve?
mscwu, It depends on which boundary condition you need extracted and used in the optistruct analysis. If it is pressure for instance, you can easily extract a txt file from acusolve results with the...
View ArticleClik here to view.
Contact problem in two different sub-cases.
Dear Administrator, I would like to know how can I properly use multiple sub-cases in a contact problem. I have done a simple example (attached) in which in the first sub-case I apply a load that...
View ArticleClik here to view.
Re: Contact problem in two different sub-cases.
Hi Vitor, What should the results actually look like? can you please describe the expected results? Secondly you do see that the loads in the horizontal direction are unopposed and will create...
View ArticleClik here to view.
Re: Contact problem in two different sub-cases.
Hello Rahul, First of all I would like to thank you for the help. About the contact I am sending you a simplified analysis in which I have two identical loads in two different load steps. What I expect...
View ArticleVWT - nothing happens after pushing RUN button
Hallo, I've got the problem that after I push the run button for my model nothing happens (local). I can see "Starting exporting/ running" in the lower left corner and a window appears with "...
View ArticleRe: VWT - nothing happens after pushing RUN button
Dominic, This is most likely due to quality issues with the model, this is often resolved by doing a good quality tria surface mesh. Please make sure you export the model from HyperMesh in...
View ArticleRe: Contact problem in two different sub-cases.
Hi Vitor, We should not expect the 2nd subcase to start from the end position of the first one. CNTNLSUB only carries over the nonlinear evolution data, for example, the gap status or plastic...
View Articlehow can i simulate Friction stir welding
From Comment in the Academic Training Center Dear Sir, i have came to know that that friction stir welding module is made by using the hyperxtrude. so if you can please tell or send me a video that...
View ArticleRe: how can i simulate Friction stir welding
Indra, Please start with the 12.0 Help guide on friction stir welding, HyperWeld > Friction Stir Welding User's Guide
View Article